WATER HAMMER??.............

This black R32 turn up for...repair.......Head gasket is gone..........But How bad?......I can see water from plug hole........And...this engine is not turning easily.......Let's check it out.

Nasty!!.........But clean piston??

Coffee milk..........

We open engine, and found gasket damage, but cannot turn crank shaft easily.....something bad feeling.

And check crank shaft......................not straight(*_*)".........So this engine has been hammering water........ the end!!!

BMW RB26!??

Today, this BMW320 race car turn up for tune........................Motec ECU........But

Look at this!........What are you doing!??............where is the BMW engine gone??

Well, RB engine is very popular but don't know about this package tho....

RB26 with GT3540 hairdryer.........

We started tune...but lots of troubles...............boost, misfire, and engine cut somehow!!

We found problem and fix one by one, but took long time to find about engine cut....Total we spend almost three days......

Finally we found...........problem... main ECU!!!.....Because of location of ECU......it was on firewall, but just behind the turbo......too much heat and maybe cook something inside??paint is burned around there!

Anyway we have a good result!!......over 400kw(550hp) at raer wheel 1.5 bar of boost.........Maybe too much??!

EVO3 with LINK PLUG IN

Evo week is still continuing...........................!?


Today we tryed with LINK G4 plug in ECU.....................This is plug in........Yes, no muck around!!!

Still you need to set air temp sensor and wire.....but not big deal??(once get use to!!?)

Inboard Map sensor is up to 1.5 bar,,,,,,,if you wanna crank b**** up....need to get extra sensor..But in this case use inboard sensor......engine is still factory set up.

This ECU is well developed and easy to set and tune ........don't know about price..How much???

SUPRA F-CON and Z33 CLUTCH......

Supra JZA80 VVTi engine!!

Today's job..........JZA80 Supra VVTi engine with F-con tune....................Made good power from just F-con and full exhaust, no boost controller only 1.22 bar...un..........need one more kick!!Just look around engine room..............And this black box is very doubtful!!

This car still has factory(lunch box alike) air box.............un.....Take big lunch box off and see what's gonna happen!?

Over 15kw gain at wheel!! just remove lunch box....over 300kw at wheel.......but injector...almost finished!! Any other restrictions???

And Z33 clutch slipping......("bloody Asian driver!!??")What?? Who say that??? I'm Asian too!!! Dick head!?

EVO DAY................

Evo, Evo, Evo day..... this week......service, tune,change exhaust system, suspension, gauge installation, and build engine...etc etc .


Takes bit time to install Defi gauges, but looks always nicer!!




And clutch......


Till this weekend...............(^_^)"""

ANOTHER CRACK..............................N1..(*_*)'

N1 Block.........But....

Crack test just in case.................need new one.....Do I?

Cr.. CRACK AGAIN.......!!

After hard driving.......at race track....sound strange.......... exhaust leak from manifold.....Well it's common problem for stainless manifold(even factory will crack)..
Solution?......buy a new one or.......In this case we have to fix it....because it's custom make!


Fond crack!!!.......


Weld on top.......hopefully last long for this time!!

It's pain in a** ....because need to remove turbo etc... So who is next!??

MANSON GTR...TRY QUARTER MILE!!??

Are you ready roach??



How quick this cockroaches can do at drag strip.....?.............Let's do quarter mile!!
This roche did 58 seconds at Puke...Ok!! Of course...cockroaches are first on the corners but... how about straight???



Still race track set up..... nothing change..........super camber.....over 1500kg.......no carbon fiber..
Well,
Yes this angry bitch did 10.06 second and over 137mile/h............ We should give her a better name rather than calling cockroaches??


And should we change set up for straight for 9sec?? I think this roche will do easily.

NEW HEAD ON PROGRESS!!

It's takes long for the cylinder head job....., open, clean, porting, set valves, simming,etc etc....................
But.....



We do most process our self...

wow!

One done.............4more to go!!?

EVO CLUTCH.................Need Twin?

Evo7 clutch......

After hard driving...............Cu....Clutch doesn't work!!....................Need super heavy duty?? Does anyone make such thing??? Super heavy duty!.......Don't wanna heavy pedal tho....!!